Rootthecause/DCDC 是一个托管在 GitHub 上的开源项目，主要使用 HTML 编写，采用 CERN Open Hardware Licence Version 2 - Weakly Reciprocal 许可证，目前获得 162 个 Star、18 次 Fork。
仓库全名
Rootthecause/DCDC
README 摘要
Dear Formula Student Teams, I've designed a High Voltage DC/DC Converter to replace our LV Battery. Feel free to use it as well! Although this design (and previous versions) have passed two times FSG scrutineering and have been operating without any issues for over 6 months, always manufacture at your own risk! If you encountered any bugs or have suggestions for improvement, please use the GitHub issues form. For…
I’ve designed a High Voltage DC/DC Converter to replace our LV Battery. Feel free to use it as well!
Although this design (and previous versions) have passed two times FSG scrutineering and have been operating without any issues for over 6 months, always manufacture at your own risk!
If you encountered any bugs or have suggestions for improvement, please use the GitHub issues form. For discussions and technical questions, kindly use the discussion bord.
This design is published as open-source hardware under the CERN-OHL-W license and can be found on GitHub: https://github.com/Rootthecause/DCDC
If you had early access to this GitHub page or received any files from me directly, please do not share or publish them, as I don’t want others to share files which may be incomplete or contain errors.
Have fun! Do not lick things with spark symbols on :)
Best regards,
Rootthecause / Liv
March 10, 2026: Thanks for giving this repro more than 100 stars! ⭐️
Updates
For recent updates on building a v9-3 replica, please read the v9-3 Build Notes.
Date YYMMDD
Description
260812
Urgent notice: The distance between F1 and RV1 is too small, which can lead to a arc on the HV side while the DCDC is enabled. As long as both components do not touch each other conformal coating would prevent the insulation fault, however the actual spacing is influenced by mechanical tolerances. As a hotfix, isolating glue can be used to fill the gap and/or low profile fuse clips (currently untested, should be less wide). The current spacings on the top copper layer between the components are sufficinet with conformal coating. More details on this issue will be added to the Build Notes soon.
260730
Currently used resonant C0G capacitors might cause converter failures. See v9-3 Build Notes for more details.
260609
Added new v9-4_dev branch. This version is currently untested and not recommended for use. Some components were improved, like D14, U1, U11, Q8, Q9, Q10, Q11. SR FETs have more vias and 20% larger cooling surface. Increased TS side control voltage from 12V to 15V for lower conduction losses.
260326
Update on v10 development currently being slowed down due to transformer issues.
260314
Release of the v9-3r1.4 update. Fixes many smaller issues and probably issue #10. See releases for more details.
260129
First public v10 schematic, see v10 development, also contains a timeline and small v9-3 update
IMPORTANT NOTICE: There was a complaint about the converter not being rules conform. Due to other personal priorities it might take some weeks to solve the addressed points. There is also the chance of some points unable to be resolved for the Version 9-3r. See issue#10 for further details.
250806
Announcing the v10 development - ideas welcome! Read more here. DCDCv10 survey.
250718
A bad F_min setting lead to repeatable FET destruction, please re-read the Build Guide Pages 35/36 if you’ve set up your replica before this change. See issue#8
*will not be updated after the DCDCv9-3r1.4 release (March 14, 2026).
Note for PCB-Orders
Always check the latest release before ordering!
There are new releases for every significant hardware change.
I do not recommend ordering from the latest repro clone, as it might contain unfinished hardware changes. However, simulation files or documents might be more recent.
Who should build this?
This project is for anyone who is keen to build a DC/DC converter for powering low voltage devices from high voltages or for research.
Unfortunately, it’s currently not a simple one-day-build (maybe 1-2 days for building and 1-2 Weeks for testing), but I’m working on it, making it as accessible as possible.
The skillset required ranges from soldering SMD components, SLA-Printing to sanding ferrite cores and winding a transformer (sanding is currently not needed anymore).
The documentation not only contains explanations of many components, but also detailed written assembly instructions.
I might also record a few instruction videos if there is a demand.
Stick with it - the results speak for themselves.
Technical Specifications
The DCDCv9-3 is a galvanically isolated DC/DC converter, designed to convert voltages from 200 V to 600 V down to 24 V with max. 500 W continuous output power. The low weight of 167 grams and the small footprint of a credit card (85.6 x 54 mm) are well suited to the automotive industry for supplying low-voltage systems from HV Batteries. The dynamic operating frequency between 90 and 200 kHz ensures high efficiency for various loads as well as good EMI compliance due to the resonant LLC soft switching topology. Customized versions allow output voltages from 12 V to 48 V.
Input Voltage Range: 200 to 600 V
Designed Output Voltage: 24 V
max. Output Power (min. 400V):
Continous: 500 W
180 Seconds: 600 W
60 Seconds: 750 W
max. continous Output Power at 200V: 300 W
max. continous Output Power at 300V: 500 W
Efficiency up to 96.9 % at 500 W load / 500 V input
Size: 85.6 x 54 mm x 45 mm
Weight: 167 grams
Features
built-in solid-state precharge
active rectification (NCP4305DMTTWG)
Galvanically isolated enable pins with self recharging start-up capacitor
undervoltage, overvoltage and overcurrent protection
low no-load power dissipation (7W-9W)
cost efficient UCC25600 LLC controller
reliable 4 A/6 A UCC21520 Gate Driver
onboard HV- and LV fuses
minimum isolation distance 4.5 mm (According to rule EV 4.3.6, Table 5, Conformal Coating: 600V DC -> min. 4 mm spacing required)
optional back side connectors for on-PCB mount
“FSG-Rules 2026 v1.1 conform”, the complaint #10 was resolved in the v9-3r1.4 release. Teams were able to pass at FSCH, FSA, FSCZ in 2026 [more to come]. NOTE: As converters are manufactured by the teams with individual components (such as the HF-litz wire), they must be able to show e.g. isolation ratings. Without this, passing the technical inspection may be at the discretion of the scrutineer.
Future plans
The main goal of this project is to create a universal approach for safe and efficient conversion of voltages.
At the moment, the converter can accept any input voltage up to at least 600V if UVP/OVP and component
Values are chosen correctly. On the output side, the step-down regulator (65V) is the limiting factors.
A VIPER06 IC could be used to achieve HV stepdown, or depending on the input voltage,
the stepdown could be could be shifted to the input side. This could also allow a self-starting converter to
be used as an SMPS in combination with a PFC. Another approach would be a bidirectional design so that the
stepdown is on the lower voltage side. Since active rectification is already implemented, bidirectional
conversion could be possible given the right IC. With the current development and rise of GaN MOSFETs,
a converter with PCB transformer in the MHz range might also be possible.
Do’s and dont’s
General
Not as much as possible, but as much as needed (words from a friend).
If you don’t test to the limits, you don’t know where they are.
Always start with low Voltage/Power and slowly increase it.
Figure out what measurements and values (step size) are important.
If issues appear, try to solve them sooner than later - but depending on type, they can be an oppurtunity to test out limits.
avoid making too many changes at once (except you want to perform multivariant testing), or be sure that the changes do not affect each other
Project specific
use short traces for anything that has to switch things (PCB design is complex, than that, but keep wire impedance low as well as parasitics)
make sure, your gate Driver provides clean on-off signals to the MOSFETs. Otherwise you’ll blow them up for sure sooner or later. Use MOSFETs with Kelvin connections if possible (and be sure about their correct wiring).
Do use Gate driver IC’s and not Gate Transformes (they suck). If possible, use Isolated Gate Drivers. Thats a good layer of protection if the half bridge blows up.
Always have a Thermal Camera at hand. There are relatively cheap options as USB-C accessories for Phones (~250€). I use one from TOPDON with an added maco lens. It’s worth every penny, not just for a DC/DC but also other FS Stuff. It will help you to find overloaded components (too hot) or non functioning compontens (no heat). Keep in mind, that there might be thermally reflective surfaces (brushed aluminium is like a mirror!).
Use your ears and nose in a quite environment while testing. Many issues can be heard (humming, cracking sounds), and some smelled (too hot component).
Be sure to add test points to your PCB while developing, which can be acessed via jumper wires or simliar. Do not attempt to measure anything directly with a probe while the converter is running, since a small slip can be enough to ruin the whole converter and maybe even do harm to yourself.
use an Oscilloscope with Isolated inputs (alternative use differential probes or an battery powered Oscilloscope) to check signals.
Replicas
Last updated: June 24, 2026
At least 4 Formula Student teams are replicating the DCDCv9-3r in 2026
At least 4 teams have successfully built and tested the DCDCv9-3r:
TU Graz Racing, Austria, 2025 + 2026
Anonymous team, Germany, 2025
Anonymous team, Czech, 2025
Anonymous team, (modified version), England, 2026
Arrabona Racing Team, Hungary, 2026
Want to add your team to this list (publicly or anonymously)?
Send me a DM on Reddit.
Thanks!
评论