nRF52840 MDK USB Dongle
A small, low-cost USB Dongle designed with nRF52840
Description
nRF52840 MDK USB Dongle is a small and low-cost development platform enabled by the nRF52840 multiprotocol SoC in a convenient USB Dongle form factor.
The design features a programmable user button, RGB LED, up to 12 GPIOs and 2.4G Chip antenna on board. It can be used as a low-cost Bluetooth5/Thread/802.15.4/ANT/2.4GHz multiprotocol node or development board. Alternatively the USB Dongle can be used as a Network Co-Processor(NCP) with a simple connection to a PC or other USB enabled device.
It’s shipped with the UF2 Bootloader, supports nRF Connect SDK, which integrates the Zephyr RTOS, protocol stacks, samples, hardware drivers and much more. The dongle can work as a Bluetooth Low Energy and IEEE 802.15.4 packet sniffer with Wireshark, and has PCBA and w/Case options to meet various scenarios.
Key Features
-
Nordic Semiconductor nRF52840 SoC
- 64 MHz Arm® Cortex-M4 with FPU
- 1 MB Flash + 256 KB RAM
- Bluetooth LE, Bluetooth mesh, Thread, Zigbee, 802.15.4, ANT and 2.4 GHz proprietary
- Arm TrustZone® Cryptocell 310 Security Subsystem
- 2.4 GHz Transceiver with +8 dBm TX Power
- GPIO, UART, SPI, TWI(I2C), PDM, I2S, QSPI, PWM, QDEC, 12-bit ADC support
- Integrated USB 2.0 Full-speed Controller
- Integrated NFC-A Tag
-
Arm Serial Wire Debug (SWD) port via edge pins
-
Up to 12 GPIOs available via edge pins
-
User programmable Button and RGB LED
-
On-board 2.4G chip antenna
-
3.3V regulator with 1A peak current output
-
VBUS & VIN Power-Path Management
-
Convenient USB dongle form factor
-
Breadboard-friendly with dual 10-Pin headers
-
Measures 1.65" x 0.7" x 0.15" (42mm x 17.78mm x 3.75mm) without headers soldered in
-
w/Case option available to provide protection and ease of use
-
Shipped with UF2 Bootloader supporting Drag-and-drop programming over USB drive
-
Built on open source, supporting nRF Connect SDK, Zephyr RTOS, Google’s OpenSK, etc.
Hardware diagram
The following figure illustrates the nRF52840 MDK USB Dongle hardware diagram.
Mechanical dimensions
nRF52840 MDK USB Dongle PCBA is a single sided 42mm x 17.78mm (1.65" x 0.7") 2.0mm thick PCB with a USB-A port and dual castellated/through-hole pins. nRF52840 MDK USB Dongle w/Case includes a high-quality plastic case in 50.8mm x 21.1mm (2.0" x 0.83") 7.6mm thick.
Documentation
We offer an extensive set of documentation such as getting started guides and developer guides, which can help you save big by reducing development effort.
Where to buy
| Approved Distributor |
Buy Now |
 |
  |
 |
|
Community support is provided via GitHub Discussions. We would love to have more developers contribute to this project! If you’re passionate about making this project better, see our Contributing Guidelines for more information.
License
This project is licensed under the Apache License 2.0 unless otherwise stated. For the full license text, please refer to the LICENSE file.
The nRF Connect SDK and its components are licensed under the 5-Clause Nordic License. See LICENSE-NORDIC for further details.
This project may include some imported or reused components that are licensed under different terms. Please refer to the license files within those components for details.
评论